The univers Z meter cabinet with the dimensions 950x300x205 mm and 72 space units (PLE) is designed for meter systems up to 355 A and fulfils the dimensional standards DIN VDE 0603-1 and DIN 43870. It is suitable for surface-mounted, flush-mounted or partially recessed installation.The robust enclosure housing is made of 1 mm thick, powder-coated sheet steel. The plastic inner lining provides additional safety. The enclosure is insulated (protection class II) and offers a degree of protection of IP31 (optionally IP44/IP54 in accordance with DIN VDE 0470-1). The degree of protection behind the door is IP3X.Cable entries are located at the top and bottom via integrated plastic flange plates. There are also lateral flange plates for the NAR connection area and knockouts on the rear for flexible cable routing.The flush-mounted door is equipped with adjustable, internal hinges, can be hinged on the right or left and has a 110° opening angle. The door is locked using latches - interchangeable with other locking systems. Cabinets from 800 mm wide or 1250 mm high have a rod lock with three-point locking.The enclosure can be flange-mounted side by side or on top of each other and can be extended modularly in 1 to 5-bay versions with 72 to 540 PLE.Note: A connection kit (accessory) is required for enclosure combinations. In the AAR area, the plastic flange plate can be removed and a SCHUKO or CEE socket outlet installed.

The univers Z meter cabinet with the dimensions 950x800x205 mm and 216 space units (PLE) is suitable for meter distribution systems up to 355 A. The housing complies with the DIN VDE 0603-1 and DIN 43870 standards and is designed for surface-mounted, flush-mounted or partially recessed installation.The sturdy enclosure housing is made of 1 mm thick, powder-coated sheet steel with a baked-on surface, the inner lining is made entirely of plastic. The degree of protection is IP31 (optionally IP44/IP54 in accordance with DIN VDE 0470-1), IP3X applies behind the door. Protection class II ensures protective insulation.Plastic flange plates are integrated at the top and bottom for cable entry. The enclosure also has lateral flange plates in the area of the NAR (for busbar bushing), the RfZ (only from a height of 1100 mm) and the AAR. There are also knockouts at the rear.The flush-mounted door is fitted with internal, adjustable hinges and can be hinged either on the right or left. The door opening angle is 110°. The door is locked using a sash lock, for widths from 800 mm - as in this model - using a rod lock with three-point locking. The lock can be replaced by other systems.The cabinets can be flanged side by side and on top of each other and are available in versions with 72 to 540 PLE.Note: A connection kit (accessory) must always be used for cabinet-cabinet connections. In the AAR area, the plastic flange plate can be removed and a SCHUKO or CEE socket outlet can be installed as an option.

The univers Z meter cabinet in the compact size 1100x300x205 mm with 84 space units (PLE) is suitable for the installation of meter distribution systems up to 355 A with a rated voltage of 230/400 V (50 Hz). In accordance with DIN VDE 0603-1 and dimensional standard DIN 43870, it is suitable for surface-mounted, flush-mounted or partially recessed installation.The sturdy housing is made of 1 mm thick, powder-coated sheet steel. The inner lining is made entirely of high-quality plastic. The enclosure has cable entries at the top and bottom with built-in plastic flange plates and knockouts at the rear. Flange plates are located on the sides in the area of NAR (e.g. busbar bushing), RfZ (only for 1100 mm height) and AAR.The door is flush with the front, fitted with internal, adjustable hinges and can be hinged either on the right or left. It offers a 110° opening angle. The door is locked using a latch and can be replaced by other locking systems if required.The enclosure offers protection class IP31 and optionally IP44 or IP54 in accordance with DIN VDE 0470-1. Protection class IP3X is provided behind the door. Protection class II (protective insulation) ensures increased safety.It can be mounted side by side or on top of each other. The meter cabinet is available in sizes from 1 to 5 bays with 72 to 540 PLE.Note: A connection kit (accessory) is required for a cabinet-cabinet connection. In the AAR area, a plastic flange plate can be removed to integrate an optional SCHUKO or CEE socket outlet.

The univers Z meter cabinet with the dimensions 1100x550x205 mm and 168 space units (PLE) is suitable for the installation of a meter distribution system up to 355 A with a rated voltage of 230/400 V (50 Hz). It fulfils the requirements of DIN VDE 0603-1 and the dimensional standard DIN 43870 for surface-mounted, flush-mounted or partially recessed installation.The housing is made of sturdy, profiled, powder-coated 1 mm sheet steel. The flush-mounted door is fitted with internal, adjustable hinges and can be hinged at an angle of 110° to the right or left. The door lock is fitted with latches and is replaceable.The enclosure fulfils protection class II (protective insulation) as well as protection classes IP31 to IP54 (in accordance with DIN VDE 0470-1), behind the door IP3X. The plastic inner lining reliably protects the installed technology. Cable entries are located at the top and bottom via plastic flange plates. There are also knockouts at the rear and lateral flange plates in the area of the NAR (busbar bushing), RfZ (only for 1100 mm height) and AAR.The meter enclosure can be extended modularly - both side by side and on top of each other. A SCHUKO or CEE socket outlet can optionally be integrated in the AAR area.Note: A connection kit is required for a cabinet-cabinet connection (accessories available separately).

The univers Z meter cabinet with the dimensions 1100x550x205 mm offers 168 space units (PLE) and is ideal for setting up a meter distribution system up to 355 A at 230/400 V, 50 Hz. The enclosure complies with the DIN VDE 0603-1 standard and the DIN 43870 dimensional standard and is designed for surface, flush or partially recessed mounting.The enclosure offers protection class IP31 (optionally IP44/IP54 to DIN VDE 0470-1) and protection class IP3X behind the door. Protection class II guarantees protective insulation. The powder-coated, baked-on sheet steel housing is 1 mm thick and robustly profiled. The inner lining is made entirely of plastic.Cable entries are located at the top and bottom via integrated plastic flange plates. There is a pre-embossing in the plastic at the rear. Flange plates are integrated at the sides in the area of the NAR (suitable for busbar bushing), the RfZ (at 1100 mm height) and in the AAR.The flush door with adjustable internal hinges can be hinged on the right or left and has a 110° opening angle. For widths of less than 800 mm, as here, a cam lock is used, which can be replaced by other locking systems.The enclosure can be flange-mounted, both side by side and on top of each other, and is available in 1- to 5-bay versions with 72 to 540 PLE.Note: When connecting several enclosures, a connection set (accessory) must always be used. In the AAR range, the plastic flange plate can be removed to retrofit a SCHUKO or CEE socket outlet.

Meter cabinet univers Z - 1100x800x205 mm, 252 PLE, IP44The univers Z meter cabinet measuring 1100x800x205 mm is ideal for surface-mounted, flush-mounted or partially recessed installation in accordance with DIN VDE 0603-1 and dimensional standard DIN 43870. With 252 space units, it supports the installation of a meter distribution system up to 355 A with a rated voltage of 230/400 V and 50 Hz.The housing is made of 1 mm thick, powder-coated sheet steel with a flush-mounted door that has internal, adjustable hinges and can be hinged on the right or left. The door can be opened through 110°. Depending on the size of the enclosure, the door is locked with a cam lock or bar lock with three-point locking.The enclosure has protection class II and fulfils protection classes IP31 to IP54. The protection class behind the door is IP3X. The inner lining is made entirely of plastic. Cable entries are located at the top and bottom via integrated plastic flange plates. There are also lateral flange plates in the area of NAR, RfZ (for 1100 mm height) and AAR.The modular design allows several enclosures to be flange-mounted next to or on top of each other. A SCHUKO or CEE socket outlet can optionally be installed in the AAR area. The enclosure sizes range from 1 to 5 bays with 72 to 540 PLE.Note: Always use a connection kit (accessory) when combining several enclosures.

The univers Z meter cabinet with dimensions of 1100x800x205 mm offers a generous 252 space units (PLE) for the professional installation of meter distribution systems up to 355 A with a rated voltage of 230/400 V, 50 Hz. Designed for surface, flush or partially recessed mounting, it fulfils the dimensional standard DIN 43870 and the requirements of DIN VDE 0603-1.The robust enclosure housing is made of powder-coated, baked-on sheet steel with a completeplastic inner lining. Protection class IP54 (optional IP31/IP44) and protection class II (protective insulation) ensure safe operation. The protection class behind the door is IP3X.Flexible cable routing is ensured by built-in plastic flange plates at the top and bottom, rear pre-embossing in the plastic and laterally integrated flange plates in the NAR, RfZ (at 1100 mm height) and AAR areas. In the AAR area, the flange plates can be removed if required - for the optional installation of a SCHUKO or CEE socket outlet.The flush-fitting door with internal, adjustable hinges can be hinged on the right or left and offers an opening angle of 110°. From a width of 800 mm, the enclosure is equipped with a rod lock with three-point locking. The cam lock can be replaced by other locking systems.The lockers can be flanged next to each other and on top of each other. When combining several lockers, the use of a connection set (accessory) is recommended. Ideal for the expansion of 1 to 5 bay systems with 72 to 540 PLE.

Meter cabinet univers Z - 1400x800x205 mm, 324 PLE, IP44The univers Z meter cabinet measuring 1400x800x205 mm is ideal for surface-mounted, flush-mounted or partially recessed installation in accordance with DIN VDE 0603-1 and dimensional standard DIN 43870. 324 space units (PLE) make it ideal for installing a meter distribution system up to 355 A at 230/400 V and 50 Hz.The housing is made of 1 mm thick, powder-coated sheet steel with a sturdy, profiled door that sits flush with the front and can be hinged either on the right or left. The door has a 110° opening angle and a latch lock. From a width of 800 mm and for enclosure heights from 1250 mm, a rod lock with three-point locking is used.Protection class II and protection types IP31 to IP54 offer a high level of safety. Protection class IP3X applies behind the door. The inner lining is made entirely of plastic. For cable entries, there are plastic flange plates at the top and bottom, a rear pre-embossing in the plastic and side entries in the area of NAR (e.g. for busbars), RfZ (only for 1100 mm height) and AAR.The enclosure can be flange-mounted side by side and on top of each other and is available in sizes from 1 to 5 bays with 72 to 540 PLE. A SCHUKO or CEE socket outlet can optionally be installed in the AAR area.Note: A suitable connection kit (accessory) is always required to connect several enclosures.

The univers Z meter cabinet with the dimensions 1100x1050x205 mm and 336 space units (PLE) is designed for the installation of a meter distribution system up to 355 A. It complies with the dimensional standard DIN 43870 and the standard DIN VDE 0603-1 and is suitable for surface-mounted, flush-mounted or partially recessed installation.The housing is made of 1 mm thick, powder-coated sheet steel with a baked-on surface and offers a robust design. The inner lining is made entirely of plastic. The enclosure has protection class IP54 (optionally IP31 or IP44) and protection class II (protective insulation). The protection class behind the door is IP3X.Plastic flange plates at the top and bottom ensure simple cable entries. There are also knockouts at the rear and side flange plates in the NAR (for busbar bushing), RfZ (only for 1100 mm height) and AAR areas.The flush-mounted door is equipped with internal, adjustable hinges and can be hinged to the right or left with an opening angle of 110°. The door is locked using a latch. A three-point rod lock is integrated for enclosures from 800 mm wide and 1250 mm high. The lock can be replaced by other systems.The meter cupboard can be flange-mounted side by side and on top of each other. A connection kit (accessory) is required when combining several cabinets. A plastic flange plate can be removed in the AAR area and a SCHUKO or CEE socket outlet can be installed as an option. Suitable for 1 to 5-bay systems with 72 to 540 PLE.

The univers Z meter cabinet with the dimensions 1100x1300x205 mm is designed for surface-mounted, flush-mounted or partially recessed installation in accordance with DIN VDE 0603-1 and dimensional standard DIN 43870. With 420 space units (PLE), it is ideal for setting up a meter distribution system up to 355 A with a rated voltage of 230/400 V, 50 Hz.The robust housing made of 1 mm thick, powder-coated sheet steel is sturdily profiled and has a flush door with adjustable, internal hinges. The door can be hinged on the right or left and can be opened through 110°. From a width of 800 mm and a height of 1250 mm, a rod lock with three-point locking is used.The enclosure fulfils protection class II and protection class IP31 (optionally IP44/IP54 in accordance with DIN VDE 0470-1). Protection class IP3X applies behind the door. The entire inner lining is made of plastic. Cable entries are made at the top and bottom via integrated plastic flange plates, and there are also knockouts at the rear and side entries for NAR (e.g. busbar bushing), RfZ (only for 1100 mm height) and AAR.The enclosure can be modularly combined - both side-by-side and stacked - and is available in sizes with 72 to 540 space units. A SCHUKO or CEE socket outlet can be installed in the AAR area.Note: A connection kit (accessory) is required to combine several cabinets.

The univers Z meter cabinet with dimensions of 1250x300x205 mm offers 96 space units (PLE) and is ideal for the installation of meter distribution systems up to 355 A. The installation can be surface-mounted, flush-mounted or partially recessed. The enclosure fulfils the dimensional standard DIN 43870 and DIN VDE 0603-1.The housing is made of 1 mm thick, powder-coated and baked-on sheet steel, which ensures a high level of stability. The inside of the enclosure is fully lined with plastic. Protection class IP44 (optional IP31/IP54) and protection class II (protective insulation) ensure a high level of safety during operation. The protection class behind the door is IP3X.Plastic flange plates are integrated at the top and bottom for flexible cable routing. There are also flange plates on the sides in the NAR and AAR areas, as well as plastic knockouts on the rear. If required, a SCHUKO or CEE socket outlet can be retrofitted in the AAR area.The flush-mounted door is equipped with internal, adjustable hinges and can be hinged on the right or left. With an opening angle of 110°, it is easy to operate. From a height of 1250 mm, the enclosure is fitted with a three-point rod lock. The cam lock is interchangeable with other locking systems.For extended systems, the enclosure can be flange-mounted side by side and on top of each other. When combining several enclosures, a connection set (accessory) must be used. Suitable for 1 to 5 bay superstructures with 72 to 540 PLE.

The univers Z meter cabinet with dimensions of 1250x550x205 mm offers 192 space units (PLE) and is designed for meter distribution systems up to 355 A at 230/400 V (50 Hz). The housing complies with the DIN VDE 0603-1 standard and the DIN 43870 dimensional standard and is suitable for surface, flush or partially recessed mounting.The degree of protection is IP31 (optionally IP44/IP54 to DIN VDE 0470-1), behind the door IP3X. The enclosure is insulated in accordance with protection class II. The enclosure is made of 1 mm thick, robustly profiled, powder-coated sheet steel, the inner lining is made entirely of plastic.The cable entries are ensured by plastic flange plates at the top and bottom as well as by lateral plastic flange plates in the area of the NAR (busbar bushing), RfZ (only for installation height ≥ 1100 mm) and AAR. There is also a pre-embossing on the rear of the plastic part.The flush-mounted door has internal, adjustable hinges and can be hinged on the right or left. The door opening angle is 110°. From a height of 1250 mm - as in this model - a rod lock with three-point locking is integrated. The door lock can be replaced by other locking systems.The enclosure can be flanged side by side and on top of each other and is available in 1 to 5 bay versions with 72 to 540 PLE.Note: A connection kit (accessory) is required to connect several enclosures. In the AAR area, the plastic flange plate can be removed and an optional SCHUKO or CEE socket outlet inserted.